ENGINE

ENGINE UPGRADES AND REBUILDS

At Burgess Performance, we offer long to short block assemblies to fit your needs - Mild to Wild.

STANDARD SHORT BLOCK KITS INCLUDE:
4130 EAGLE ROTATING ASSEMBLY
BORE BLOCK
CLEAN BLOCK
CLEARANCE BLOCK
CAM BEARINGS INSTALL
FREEZE PLUGS INSTALL
DECK BLOCK
FILE FIT RINGS
ASSEMBLE ENGINE
CUSTOM ROLLER CAMSHAFT
ADJ. TIMING CHAIN
BALANCE ENGINE

RACE SHORT BLOCK KITS INCLUDE:
ALL OF THE STANDARD KIT PLUS
4340 RODS AND CRANK
H-SERIES BEARINGS
JE OR SRP PISTONS

RACERS SPECIAL 355-383 INCLUDING LT1 SHORT BLOCK 1499.00

We start with a GM 2 or 4 Bolt block, clean, crack check and bore and hone with Torque plates on. New cam bearings and freeze plugs installed, ESP cast crankshaft by Eagle and a set of 5140 rods with Hyperutetic pistons and Clevite bearings. It will be assembled and ready for your camshaft and heads. If you need a camshaft or a set of heads that is not a problem either. If any additional info is need please contact me. This price does not include shipping.

468-485 Cu.In. BBC Truck Pull Engines 10000.00

We start with a GM tall deck 4 bolt main block, clean, mag, and bore to spec. A 4340 Steel crankshaft and 4340 H-beam rods with JE/Probe type high dome pistons, Melling oil pumps, Clevite bearings, Plasma rings, custom ground roller camshaft, Dart 308 or 345 heads will be prepped, undercut stainless valves with titainum retainers, Competition intake, SFI approved balancer, and a set of Polished valve covers. If any other questions contact us. This does not include shipping.

 

 

 

Aftermarket blocks and cylinder heads are available for all combos. Call for pricing.

Many other options are available to meet your needs. Just give us a call.

 

 

 

COATING

CERAMIC AND POWDER COATING

Standard one piece 1 5/8" V8 set, 1 3/4" tube	$220.00*
—Multi-piece sets add $45.00
2" tube one piece headers	$240.00
—Multi-piece 2" sets add $45.00

Recoated headers may vary, due to blasting.
Preparation required for coating.
If you need any other information, please let us know.
These prices do not include shipping.

LS1

At Burgess Performance we offer 98-02 LS1 Tuning with the latest in EFI technology. No need to worry about that hand held programmer. Also we offer tuning for most any GM Truck or SUV (4.3-5.3-6.0-8.1) 4-6-cylinders available as well - Let Burgess Performance do all the work for you.

98-02 LS1 F-body tuning for NA cars
98-02 Forced Induction and Nitrous cars

BASIC TUNE INCLUDES:

• Rev limiter adjustments
• Speed limiter adjustments
• Gear changes/speedo adjustments
• Shift points/firmness
• Timing adjustments for the most power
• Delete codes and much more

$150.00 ls1 camaro only
$175.00 for 1998 ls1 f body 
Base tune with dyno time 125.00 a hour usually no more than 1-1.5 needed for this starting at 275.00

Base tunes for trucks $250.00 

W/B TUNING FOR MODIFIED CAMMED/NITROUS/FORCED INDUCTION

• Full Tune using a w/b O2 Sensor to verify and adjust fueling

$250.00 and up for street tuning n/a and nitrous ls1 camaro only. 98 add 50.00
$350.00 forced induction ls1 camaro only.
$300.00  for w/b gm truck street tuning n/a and nitrous.
$350.00 for gm truck forced induction. 

DYNO TUNING AVALABLE AS WELL(CALL FOR INFO) starting at 275.00 for base tunes and 375.00 for wide band tuning on ls1 cars.

ls1 cars only:

Rear O2, AIR & EGR Codes Delete	$40.00
Injector Change	$30.00
Lower Fan Temps	$25.00
Rear Gear Change	$25.00
Remove CAGS	$25.00
Auto Tranny Adjustments	$40.00

If you need more than one of the above, take the following discount:

         - 2 Items, $10.00 Off of total

         - 3 Items, $20.00 off of total

         - 4 or more Items, $30.00 off of total

Tuning Disclaimer:

All tuning performed on your car is for "Off Road Use Only"!   Testing and tuning on & off the dyno will push your vehicle to its mechanical limits. It is the car owner's responsibility to ensure that the car is in good working order and capable of handling the stresses incurred when tuning your car.

 

 

We Also offer installs on EDGE Torque converters for your LS1. This converter including install is only $800.00 for street version.

 

GUARANTEED .50 OFF ET'S from converter.

 

IF HEADERS ARE WHAT YOU ARE LOOKING FOR, THEN LET BURGESS PERFORAMNCE SELL OR INSTALL YOUR LS1 HEADERS.

PACE SETTER HEADERS FOR LS1

98-02 70-2256 $289.99 (UNCOATED) OR $689.00 INSTALLED W/ Y-PIPE
98-02 72C-2256 $444.99 NO AIR OR EGR RACE (COATED) OR $825.00 INSTALLED W/ Y-PIPE
98-02 Y-PIPE 82-1163 $149.99 (UNCOATED)

 

LS1 INFO AND FACTORY SPEC INFO
http://www.smokemup.com/tech/ls1.php

 

IF A LS1 IS NOT YOUR THING, WE ARE NOT PARTIAL. WE OFFER ALL THE SAME FAVORITES FOR THE LT1 GUYS TOO.

LT1 HEAD OPTIONS AVALABLE:

205CC STREET HEAD 64CC 1510# $2,167.00 CNC'D
225CC STRIP HEADC 64CC 1610# $2,449.00 CNC'D
72CC 1630# $2,349.00 CNC'D

This is only a small portion of what we offer for your ls1, Give us a call if there is something your looking for.

 

Manufactures and specialized GM F-body suspension parts.

 

 

 

PROFESSIONAL PRODUCTS

80MM-85MM LS1 THROTTLE BODIES
STARTING AT 199.00
POLISHED OR SATIN FINISHES

LS1 INTAKES WITH RAILS
STARTING AT 399.00
POLISHED OR SATIN FINISHES

LS1/LS2/LS6 24 TOOTH RELUCTOR@ LQ9/LS2 6.0 IRON BLOCK

COMPETITION ROTATING ASSEMBLIES 347-408 2399.00 SHIPPED.

All Eagle Competition assemblies include our forged 4340 chromoly crankshaft, our forged 4340 chromoly H-beam rods, forged JE pistons, Clevite77 race bearings, and JE Rings. All are designed for internal balance.

Recommended for use up to 750 HP (1500 HP with optional ARP L-19 bolts)

 

 

 

EFI

EFI TUNING

If hand held programers are out of your price range and hard to understand what you are paying for, then let Burgess Performance do all the work for you with our latest in affordable factory ECM tuning.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

GM V8 GEN III CARS/TRUCKS
GM V8 IV CARS/TRUCKS
V6 CARS/TRUCKS

MOST TRUCKS WITH OBD11 APPLY, CHECK WITH US ON YOUR APPLICATION

If you are looking to spend more money on a stand alone EFI set-up, then let Burgess Performance sell, install and tune your application - F.A.S.T. and Big stuff options available. If installing is your thing, then give us a call to get your set-up with a start up program.
n3n16629.jpg

87-07 MUSTANG

For all you Ford guys out there, if a chip is what you are looking for, look no further and let Burgess Performance custom tune a chip for your application.
N/A - FORCED IND - NOS
GIVE US A CALL
MOST PROGRAMS STARTING AT $379.00
DYNO TUNING AVALABLE STARTING AT 150.00 A HOUR(Call for details)

If wiring is not your thing, then no problem- Burgess Performance will wire your complete car from Stand Alone ECUs, Wideband O2 sensors, Gauges, Painless Wiring Panels, Timers, Nitrous Systems and Complete Cars and much more. We also can get custom ECU harnesses and plug in adaptor harnesses.

SUSP

Please not the buy now button is set-up to accept any and all products listed on site. Burgess Performance will need to be contacted prior to purchase for you to get total of products wanted and shipping total. Thank your for your understanding! 

 

SUSPENSION

At Burgess Performance, we offer a variety of choices for all your racing suspension needs. From Mustang to F-Body, we got it. Suspension packages from AJE Racing, QA1, Southern outlaw shop and more. We can install and set up your suspension for drag racing or street.

SOUTHERN OUTLAW SHOP SUSPENSIONS (PRICING BASED ON A FOX BODY MUSTANG)

ROLL CAGES (CHROMOLY) starting at  weld in.675.00
SUBFRAME CONNECTERS THRU FLOOR 179.00
TORQUE BOXES 20.00
UPPER LWR KIT 85.00
MINI TUBS 130.00
CHUTE MOUNTS 299.00
ANTI ROLL BARS starting at 275.00 SINGLE ADJ
REAR BULK HEADS starting at 125.00
8.8 BRACE KIT 95.00
DRIVESHAFT LOOP 59.00
COIL OVER CONVERSION 120.00
WINGS STARTING AT 179.00
9IN BRACED REAR CASE ONLY STARTING AT 475.00
AND MUCH MORE.....Kits at suspension parts available for F-Body,GN,G-body

QA1 SUSPENSIONS
SUSPENSION KITS
SHOCKS
STRUTS
CONTROL ARMS
AND MUCH MORE.

SPOHN PERFORMANCE FORD MUSTANG(05-08) & GM G-BODY, A-BODY, B-BODY, F-BODY AND S-10

SUSPENSION(LOWERS,UPPERS,TQ ARMS,PANHARD ETC)
CHASSIS (SUB FRAMES, K-MEMBERS,STRUT BRACES)
DRIVETRAIN
ROLL BARS
BRAKES
AND MORE....Call for pricing

Baseline Suspensions
Prolaunch Series Suspension Parts, Get MORE CONSISTANT 60 ft times!
Angle the Upper Control Arms like a TRUE 4-LINK to keep from unloading the tires
Correct Instant Center Position, Proper Antisquat, Better TRACTION, Better WEIGHT TRANSFER
JUST LIKE IT SHOULD BE!! Prolaunch kits available as well. Call for details!

260.00
Street-Launch - Recommended for cars running Low 11's.
For '79 and newer Mustangs equipped with the 8.8 rear end.
Includes Polyeurathane Chassis Bushings, Heim ends on the axle side and new hardware.
Prolaunch#2 for low 10's cars 260.00 and a Prolaunch#3 for mid 7's 360.00 are available as well.

175.00
LCA #1
Lower Control Arms
Direct Bolt-In with Solid bushings on both ends.
TIG welded Chromemoly
Single Adjustable
5/8" x 1/2" Chromemoly Heim ends
Standard with 1/2" control arm bolts
With Spring perches
Does not use swaybar.

360.00
#2 ARB (Anti-Roll Bar) RACE
More Room for 3" tailpipes
TIG welded Chromemoly construction
Replaceable Bronze Chassis Bushings
1/2" heim ends for down links
* Weld-in or Bolt-in Construction
** More clearance for 3" exhaust

238.00
#3 ARB (Anti-Roll Bar) RACE
More Room for 3" tailpipes
TIG welded Chromemoly construction
Frame Mount WELD-IN construction
Bronze Chassis Bushings
1/2" heim ends for down links
** More clearance for 3" exhaust

185.00

LCA #3
Offset Chromemoly Lower Control Arms
TIG welded Chromemoly
Double Adjustable
Offset for larger tires
5/8"x5/8" Chromemoly Heim ends, LARGER 5/8" control arm bolts
No Spring perches

160.00

LCA #3
Offset Chromemoly Lower Control Arms
TIG welded Chromemoly
Double Adjustable
Offset for larger tires
5/8"x5/8" Chromemoly Heim ends, LARGER 5/8" control arm bolts
No Spring perches

130.00

Upper Control Arm Upgrade Kit
Update your Prolaunch #1 kit to a Prolaunch #2 Kit.
Includes Chromemoly control arms, LARGER 5/8" control arm bolts, 5/8"x5/8" Chromemoly Heim ends, 5/8" control arm bolts, etc.
Redrilling of your existing brackets to 5/8" is required.

33.00

Antiroll Bar Bronze Bushing Kit
Need a Christmas Idea?
Want to train your goldfish to jump through hoops?
OR update your Street Antiroll Bar to a Race Antiroll Bar with these bolt-in bushings. Uses your existing hardware.

68.00

Pro-Launch Track Locator
If you already have a Prolaunch #1 OR #2 upper control arm kit then this is what you need.
Center the rearend under your car the EASY WAY!
Increase launch stability and top end stabilty!
Specify control arm bolt size when ordering: 1/2" bolts or 5/8" bolts
*Fits all exhaust systems.
*Bolt-in. No welding necessary.
**This part ONLY works with the Prolaunch #1 and #2 Upper Control Arm kits. Not recommended for use with Street Launch kit.

AJE RACING
AJE suspensions are very good value if you want to go fast and look good! These are A DIRECT BOLT-IN!!!

 

PARTS AVAILABLE FOR G-BODY F-BODY

A-BODY C5 VETTE IMPALLA SS AS WELL......

CALL OR E-MAIL FOR DETAILS AND PRICING

 

 

 

 

 

 

NITROUS

 

Let us help you with your nitrous system. we can do all the wiring, switches, relays, timers and hard-line plumbing. Don't melt your pistons - get the facts first.

 

FORCED IND

FORCED INDUCTION

At Burgess Performance, we offer many forced induction choices from EFI to blow through carb, intercooled or not. let us help you in whatever fits your needs - from the strip to the street, give us a call.

CALL FOR PRICING

 

CALL FOR PRICING

PAXTON

CALL FOR PRICING

 

 

750cfm blow through carb
$875.00

850cfm blow through carb
$1050.00

blow through carb w/
dual needle & seat bowls
$1550.00

PORTING

Porting Labor Costs

$400Stage 1- Port match the intake runner, blend the bowls on the intake and exhaust valve pocket.

$600 Stage 2- Everything offered in the stage 1 plus working the short side radius Intake and Exhaust, Shape the intake runner roof, unshroud and polish the combustion chamber, and polish the exhaust port.

$800 Stage 3 Everything offered in the stage 1 and 2 plus emphasizing work to utilize the flow rates at all the lift ranges of the camshaft used.

There is a $75.00 discount applied to any port work when added to a new head order.

Add $150.00 to Stage cost for porting cast iron heads.

DIESEL

Here at Burgess Performance we speak diesel as well. Burgess Performance is a dealer for a wide variety of performance diesel products available on the market today. Here at Burgess Performance you can experience the same great deals offerered by those other guys with such products like, ATS,BD Diesel,Banks Power,Bully Dog,FASS,Smarty,MBRP and many more. So feel free to call Burgess Performance and let us set your Diesel up with whatever fits your needs, Pull,Drag,Mud or just every day cruiser.

 

OTHER EDGE PRODUCTS AVAILABLE AS WELL, IF APPLICATION NOT SEEN FEEL FREE TO GIVE US A CALL FOR ANY DIESEL PRODUCT YOU MAY BE LOOKING FOR. CALL FOR PRICING ON ANY DIESEL ITEMS

INTERCOOLERS

CUSTOM INTERCOOLERS AVAILABLE PER APPLICATION PLEASE CALL FOR PRICING. 

PAINTBODY

Burgess Performance now offers a paint and body service to it customers in continued effort to include all your automotive needs. Call for estimates

 

 

 

 

 

FUELS

110 octane 369.00 a barrel no barrel fee
112 octane 422.00 
116 octane 534.00 
ALKY 159.00 

These prices are me picking up at my distributor min of 2 barrels for this. If you have a 4 or more min barrel order call for price difference. Also there will be no barrel deposit fee for this fuel! Prices are always subject to change at anytime. If interested im taking orders for first load so need you to prepay before order. If there is a product not listed on here feel free to give us a call and we will get you what you need.

SCALING

Burgess Performance offers in house scaling for your drag or street car.. From your basic just to check total weight, to full adjustments where needed..

Base scale with minor adj, with stock style suspension 150.00
Call for other prices if needed.